For some die-cast parts, the as-cast geometry is ready for use. Others need a sealing surface, seat, hole, or thread completed by machining. Make this decision before the die is finalized so the raw casting, datums, and tool access align with the finished product.

For an order review, clarify three points: which feature must be finished, what limits the drawing specifies, and how the feature will be inspected.

Convert Functional Needs into Measurable Features

Start with how the part is used. A gasket-contact surface, shaft seat, and mounting-hole location have different needs. For each feature, state size, geometric relationship, and surface condition on the drawing; then assess whether it can be achieved as cast or requires machining.

NADCA explains that some castings are ready for use after ejection and trimming, while others need secondary operations. Producing internal threads is one application of machining. [1]

Which Features Commonly Require a Machining Review?

The table below is a guide for discussing the drawing. Operations, tooling, and acceptance limits are selected after reviewing material, geometry, and volume.

Part FeatureWhat Must Be Defined
Joint or sealing surfaceDimensions, surface quality, and relationship to datums
Mounting or locating holeDiameter, depth, and position relative to drawing datums
ThreadType, size, engagement length, and inspection method
Interrelated featuresGeometric relationship and feasibility of manufacturing and inspection in the operation sequence

For example, specifying a hole diameter without locating it relative to the mounting surface may not provide enough information to assess assembly. Nor do all visible surfaces require the same finish. Distinguish functional, cosmetic, and noncritical surfaces so operations are specified only where necessary.

Review the As-Cast and Finished Part Together

The finished model shows the delivered product; the as-cast model should also define removable material and reliable surfaces for holding the part. Machining allowance depends on geometry, casting variation, and operation sequence and is not a fixed value for every part.

Machining may expose pores already present below the cast surface. Menzies and Koshy studied this phenomenon in cast components. [3] A pore seen after material removal therefore does not by itself prove that machining created it. Review the defect location, as-cast condition, stock removal, and machined-surface quality together.

Datums and Fixtures Are Part of the Engineering Decision

A datum is the reference used to define dimensions and geometric relationships. A fixture holds the part during an operation. In workholding design, coordinate support points, operation sequence, and tool access with the drawing datums. Deformation caused by clamping should also be considered when evaluating manufacturing and measurement methods.

A CNC machine name does not guarantee a particular tolerance. Material, geometry, as-cast condition, tooling, machine condition, and measurement method all affect the result. Committable limits must be assessed for the specific feature and production method.

Measurement probe on the company's machining equipmentImage source: Novin Industrial Group archive

Define Post-Machining Inspection from the Start

Connect inspection to drawing features from the outset: dimensions and geometric relationships, threads, edge condition, and functional tests each require a suitable method. If leak testing is required, state its conditions, production stage, and acceptance criterion in the order.

Renishaw describes probe use for part setup and in-cycle inspection on machine tools. [2] Such measurement covers only accessible features defined in the program. Probing several points is not a complete inspection of all dimensions, internal quality, or part function. Method adequacy and measurement error should be assessed relative to the tolerance.

Residual chips, burrs, and handling damage can also create assembly problems. Define cleaning, surface protection, and packaging together with the main operations.

What Information Should You Send for a Machining Review?

Send the controlled drawing, as-cast model, material, volume, and status of raw-part supply. If providing a sample, state which feature is the reference and what change is required. A used sample helps explain the part, but dimensions and acceptance criteria must be clear in the order documents.

Novin Industrial Group provides machining both as part of the integrated component-production chain and for standalone orders. Operation scope, raw-part supply, and sample approval are defined in the review of each order. See the Machining & Finishing page for details, or submit information through Start a Project .

Before Ordering Machining

  • Identify the drawing and final-model revision.
  • Send the as-cast model or specification with the order.
  • Mark datum surfaces and critical assembly features.
  • Define threads, surface quality, and required tests.
  • State production volume and delivery schedule.
  • Agree on raw-part supply and the sample-approval criterion.

Frequently Asked Questions

Do all die-cast parts require machining?

No. The need for secondary operations follows from part function, drawing characteristics, and whether they can be achieved as cast. Some parts are ready after trimming; other features require later operations.

Can tolerance be determined simply by selecting a CNC machine?

No. Machine designation alone is insufficient. Material, geometry, datums, fixtures, operation sequence, and inspection method must also be reviewed for the part, and committable limits should be clear in the drawing and technical agreement.

Is a physical part sample enough for an initial review?

A sample helps explain the part. To define a manufacturing commitment, a drawing or additional information about dimensions, material, application, volume, and acceptance criteria will also be needed.

References and Further Reading

  1. NADCA Design — Secondary Processing Costs ↗The need for secondary operations on die-cast parts and the role of machining in completing part features.
  2. Renishaw — Probing and tool measurement systems for machine tools ↗Use of probes and tool-measurement systems for setup and in-process inspection.
  3. Menzies, I.; Koshy, P. (2009) — In-process detection of surface porosity in machined castings ↗Study of surface porosity exposed during machining of cast components.2009 · DOI: 10.1016/j.ijmachtools.2008.12.008

Machining Order Review

Specify the drawing, quantity, material, and raw-part condition. Datums, surfaces to be finished, and inspection criteria will be reviewed during process planning.

View the Related Capability → Send Project Information and Start a Review

Related Articles

What Is DFM for Die-Cast Parts? Product-Design Principles for HPDCWhat Information Should You Prepare for a Production RFQ?From Prototype to Series-Production Approval

Back to All Insights →