Alloy selection becomes more reliable when the part's application and manufacturing conditions are clear. An alloy suitable for a typical housing is not necessarily the best choice for a part with different thermal, cosmetic, or assembly requirements. The decision should consider the full set of requirements together.

For the customer, the desired output is a referenceable specification: the alloy designation and standard, supplementary requirements, verification method, and expected records. Phrases such as “high-quality aluminum” or a trade name alone do not define the scope of this agreement.

Start with the Part's Service Conditions

Before comparing alloy designations, collect the application data. What loads must the part carry, in what environment will it operate, and which components will it contact? Is surface appearance important, or do thermal and dimensional performance take priority? If the drawing already specifies a grade, the review should begin with that requirement, and any proposed change should be approved by the responsible engineer.

NADCA presents alloy selection as a combination of technical and economic criteria, including structural properties, corrosion resistance, surface condition, machinability, and process cost. This multi-criteria approach helps prevent a decision based solely on metal price. [1]

Turn Part Requirements into Technical Questions

Project RequirementQuestion to Answer Before Selection
Mechanical PerformanceWhat are the loads, installation conditions, and critical drawing characteristics?
Service EnvironmentHow will the part be exposed to moisture, environmental agents, or heat?
Appearance & CoatingWhat are the acceptance criteria for the as-cast surface, paint, or surface treatment?
Manufacturing & FinishingWhat constraints arise from geometry, wall thickness, machining, and assembly?

For every critical characteristic, also state how it will be evaluated. If the appearance of a coated area matters, for example, naming the coating is not enough; define the relevant surface area, a reference sample, or an acceptance criterion. This information allows the alloy and the process to be assessed together.

State the Grade and Reference Standard Explicitly

Record the grade together with the reference standard, revision, and supplementary requirements. The Aluminum Association's Pink Sheets document the designations and chemical-composition limits for casting alloys and ingot. [3] That designation alone does not establish the mechanical properties of the manufactured part.

A similar trade name is not authorization to substitute a material. For any proposed alternative, compare the specification limits and have the effect on manufacturing and performance approved by the responsible engineer. If heat treatment or surface treatment is required, its compatibility with the material and production method should also be evaluated separately.

Evaluate Chemistry Alongside Part Performance

NADCA identifies distinct characteristics among aluminum die-casting alloys; the grade should therefore be selected against the requirements of the specific part. [2] Optical-emission spectrometry provides information about a sample's chemical composition, but it does not by itself determine microstructure, porosity, or mechanical performance.

In one die-casting study of an Al–Si alloy, changes in flow conditions were accompanied by changes in microstructure, porosity, and tensile-test results. [4] The experiment used a specific runner geometry and operating conditions; its findings are not a general instruction to change injection speed. For an order, clarify whether property data were obtained from a separate test coupon or the actual part, and whether the manufacturing method and test conditions are relevant to the application.

Aluminum ingots in the Novin Industrial Group image archiveImage source: Novin Industrial Group archive

Define the Material Supply and Control Route

Define who is responsible for supplying the material, the acceptance specification, and the required disposition if a nonconformity is found. If the customer supplies the material, the grade and lot identification should accompany it. Analysis results should also be traceable to the relevant sample or melt so the material report remains usable.

Novin Industrial Group controls material chemistry by optical-emission spectrometry. The grade, supply method, and required documentation for each order should be defined in the technical agreement. The Alloy Preparation & Melt Control page explains the related stages.

Turn the Final Selection into a Traceable Agreement

Record the final specification in the drawing, purchase order, or another controlled technical document. Also identify who may approve a substitution, how the material will be verified, and which records are required. For repeat orders, the same revision should remain the reference for sourcing and inspection.

For an initial review, prepare the application, drawing, current or proposed grade, production volume, and surface and performance requirements. If the goal of changing material is to improve a particular characteristic, describe how it will be evaluated so alternatives can be compared against a common criterion. Submit the information through Start a Project .

Alloy Specification Checklist

  • Describe the part's application and service conditions.
  • Identify the grade and reference standard on the drawing.
  • Prioritize the critical performance and appearance characteristics.
  • State the required machining and surface-treatment operations.
  • Define responsibility for material supply and records.
  • Require documented engineering approval for any grade change or substitution.

Frequently Asked Questions

Can grades with similar names be substituted for one another?

A substitution should be reviewed by comparing the specifications and project requirements. A similar trade name or common application does not prove that grades are equivalent or authorize a material change.

Does spectrometric analysis guarantee the final quality of the part?

The analysis verifies chemical composition. Acceptance of dimensions, appearance, and part performance requires project-specific controls and tests and should be defined independently of chemistry approval.

Where should we start if we do not know the appropriate grade?

Provide the drawing or sample together with the application, environmental conditions, volume, and performance requirements. These data form the basis for reviewing options, and the final selection should be recorded in the agreed specification.

References and Further Reading

  1. NADCA Design — Alloy Selection ↗Technical and economic criteria for selecting a die-casting alloy.
  2. NADCA Design — Aluminum Alloys ↗Overview of aluminum die-casting alloy families and their differing characteristics.
  3. The Aluminum Association — Pink Sheets: Designations and Chemical Composition Limits for Castings and Ingot ↗Reference for designations and chemical-composition limits of aluminum casting alloys and ingot.
  4. Gunasegaram, D. R.; Finnin, B. R.; Polivka, F. B. (2007) — Melt flow velocity in high pressure die casting: Its effect on microstructure and mechanical properties in an Al–Si alloy ↗Effect of flow conditions on the microstructure and properties of CA313 alloy specimens in a defined experimental arrangement.2007 · DOI: 10.1179/174328407X176992

Define the Material Specification for a Production Order

State the required grade or standard and the part's service conditions. The material specification, control method, and agreed records should be clarified during review of that specific order.

View the Related Capability → Send Project Information and Start a Review

Related Articles

Which Parts Are Suitable for Die Casting?Common Die-Casting Defects: Causes and InvestigationHow Do Production Traceability and Monitoring Support Quality?

Back to All Insights →